Products Description
A cost effective, one-part, acetoxy cure silicone sealant for general purpose applications. It provides a flexible bond and will not harden or crack. It is a high performance sealant, with +-25% movement capability when properly applied. It offers long term durability in a range of general sealing or glazing applications on glass, aluminum, painted surfaces, ceramics, fiberglass, and nonoily wood.
Features & Benefits
1.One-part room temperature cured silicone sealant;
2.Good flexibility after cured;
3.Good adhesion to glass and ceramic materials.
Applications
1.Window and door glass filling and sealing;
2.Glass to glass adhesion and sealing;
3.Ceramic materials adhesion and sealing;
4.General industrial sealing and bonding application.
| Consumption (approx.) |
| Joint Width | 6mm | 9mm | 12mm |
| Joint Depth | 6mm | 6mm | 6mm |
| Efficiency/300ml | 8meters | 6meters | 4meters |
| Consumption (approx.) |
| Following cleaning procedure and materials are recommended: |
| Glass | Degrease with alcohol or MEK |
| Aluminium, light alloys and stainless steel | Degrease with alcohol or MEK |
| Other Metals | Lightly abrade then degrease as above |
| Wood | Lightly abrade surface then remove dust |
| Plastics | Degrease using an agent recommended by plastics manufacturer |
Instructions
1.Ensure that surfaces to be sealed are clean, dry and grease free;
2.The application temperature must be between +5 ℃ and +40℃;
3.After the application,the sealant must be tooled with light pressure within 5 minutes to spread the material against the joint surfaces and to obtain a professional finish;
4.Excess uncured sealant may be cleaned with solvent. Cured sealant can be removed barely mechanically;
5.6mm. joint depth is recommended for joint widths between 6 mm to 12 mm;
6.After the construction of aquarium is complete, wait for minimum of 21 days before usage.
Standards
Meets or exceeds the requirements of the following specifications:
1.ISO 11600 F & G 20LM;
2.CE marked for EN 15651 for façade, glazing and sanitary;
3.The requirements of VOC content specifications in LEED credit EQc4.1 "Low-emitting products" of SCAQMD rule 1168.
Restrictions
If you need advanced sealant used for curtain wall construction, please contact your local representative.
This product is not suitable for the following purposes:
Materials that bleed plasticizers or solvents or release by-products that may inhibit its cure, affect adhesion or discolor the sealant Unventilated places;
This product is neither tested nor represented as suitable for medical or pharmaceutical uses.
Safety & Disposal
Inhalation of the sealant vapor for a long period must be avoided. The application area must be ventilated proper-ly. The uncured sealant must not be contacted for a long period. Cured silicone rubber bears no risk to health.tem-peratures between +5℃ and +25℃. Check MSDS guide-lines for disposal and further information concerning safety.
Storage & Shelf Life
Stored properly in a dry and well-ventilated place below 30℃.
Usable life is 24 months in original package.
More information refer to package.
| TDS |
| Performance | Standard | Measured Value | Testing Method |
| Test at 50±5%RH and tempera ture 23±2℃: |
| Density(g/cm3) | ±0.1 | 0.96g/ml | GB/T13477 |
| Tack-Free Time(min) | ≤180 | 8 | GB/T13477 |
| Extrusion g/5S | ≥150 | 600 | GB/T13477 |
| Tensile Modulus (Mpa) 23℃ | ≤0.4 | 0.30 | GB/T13477 |
| -20℃ | or ≤0.6 | 0.45 |
|
| 105℃ weight loss,24hr % | / | 40 | GB/T13477 |
| Slumpability(mm)vertical | ≤3 | 0 | GB/T13477 |
| Slumpability(mm)horizontal | Not change shape | Not change shape | GB/T13477 |
| Curing Speed(mm/d) | 2 | 3.5 | / |
| As Cured-After 21days at 50±5%RH and temperature 23±2℃ |
| Hardness(Shore A) | 20~60 | 23 | GB/T531 |
| Tensile Strength under |
|
|
|
| Standard Conditions(Mpa) | / | 0.26 | GB/T13477 |
| Elongation of Rupture(%) | / | 400 | GB/T13477 |
| Movement Capability(%) | 12.5 | 12.5 | GB/T13477 |
| Skin Formation | 10minutes |
|
|
Tel: +86-15966176633
